Electrical Instrumentation Technician Resume Samples

Description :

1. Used mathematics to perform any and all calculations required for the position.
2. Ran PVC conduit pulling electrical wire and Read and understood electrical blueprints, drawings, and schematics.
3. Contributed and delivered high-quality toolbox talks and Maintained good housekeeping in the workplace.
4. Read and understood electrical diagrams and schematics and Installed, maintained, and calibrated process control and instrumentation equipment including, but not limited to, flow meters, thermocouples, RTDs, transmitters, weigh feeders, starters, DC drives, AC drives, VFDs, and emissions analyzers.
5. Calibrated and maintained all emissions analyzers in accordance with service manuals and regulatory permit requirements.
6. Maintained instrument logbook on all maintenance activity and Ensured process control data was being recorded, backed up, and archived.
7. Performed maintenance on existing instrument equipment and Performed new instrumentation construction installation.

Experience

10+ Years

Level

Senior

Education

Associate's Degree In Instrumentation Technology

Description :

1. Experienced in diagnosing, repairing, or replacing drives including but not limited to Allen Bradley, Toshiba, Eurotherm, Yasakawa, Reliance, and GE.
2. Experienced working with pulp and paper, converting equipment, and/or packaging equipment.
3. Experienced reading and following control schemes, and electrical, and maintenance schematics/blueprints.
4. Experienced troubleshooting/repairing various types of pumps and fluid systems.
5. Experienced programming and troubleshooting programmable logic controls (PLCs).
6. Assisted crew members and worked in a team environment; communicating effectively and constructively.
7. Experienced working with Industrial Controls, e.g.: motor controls, control valves, and industrial instrumentation for flow, level, pressure, and temperature.

Experience

7-10 Years

Level

Management

Education

Associate's Degree In Electrical Engineering Technology

Description :

1. Inspected, repaired, replaced, and optically aligned A/C electric motors and A/C, and D/C drive systems.
2. Performed testing, adjustments, calibrations, and servicing activities
3. Inspected, repaired, and reset voltages, Ensured that distributive control systems were aligned and calibrated so panel operators could rely on process adjustments including manual and automatic.
4. Set and calibrated sensors and warning alarms, Prepared sketches or followed blueprints to determine the location of the wiring or equipment and to ensure conformance to building and safety codes.
5. Maintained safe working conditions in accordance with established Company policies.
6. Troubleshooted and analyzed instrument, control, and metering problems, and took appropriate action to correct deficiencies.
7. Troubleshooted and analyzed High/Medium Voltage electrical equipment and system problems and took appropriate action to correct deficiencies.

Experience

5-7 Years

Level

Executive

Education

Associate's Degree In Electrical Engineering Technology

Description :

1. Maintained and calibrated measurement devices such as thermometers, pressure gauges, flow meters, ammeters, voltmeters, and hydrometers.
2. Repaired or replaced damaged electrical wiring or equipment such as light fixtures, switches, circuit breakers, fuses, and transformers.
3. Improved and modified preventative maintenance activities as appropriate.
4. Utilized drawings, prints, and instruction manuals to determine the proper steps to be taken for equipment preventative maintenance, troubleshooting, and repairs.
5. Adhered to company drawing and documentation standards.
6. Used logic when troubleshooting problems to arrive at solutions.
7. Communicated effectively across multiple levels and functions. 

Experience

2-5 Years

Level

Executive

Education

Associate's Degree In Electrical Engineering Technology

Description :

1. Followed all safety, including lockout/tagout, and sanitation procedures.
2. Cross-trained whenever possible to help achieve a more efficient Maintenance Department and provide feedback for needed training.
3. Provided training for new operators and professional personnel and Verified competence of operators.
4. Participated in or led departmental audits, housekeeping inspections, and other specialty SHE audits as appropriate.
5. Worked in confined spaces and wore self-contained breathing apparatus or fresh air mask.
6. Repaired and maintained cameras and kiln scanners, Inspected, PM, and maintained generators.
7. Inspected, PM, calibrated, and maintained Pfister and other feeders, Inspected, PM, and maintained MCCs and Transformers.

Experience

2-5 Years

Level

Executive

Education

Associate's Degree In Electrical Engineering Technology

Description :

1. Performed preventative maintenance on assigned equipment in customer and company facilities.
2. Effected electrical maintenance in accordance with all local and national codes, Identified, reported, and/or corrected issues that would create an unsafe work environment.
3. Worked on logic diagrams, electrical and mechanical drawings and sketches, and other written instructions.
4. Completed preventive, corrective maintenance, and scheduled maintenance.
5. Improved operation of systems, instruments, controls, and metering and electrical equipment installed in plants and in customer facilities.
6. Advised Supervisor when work is beyond the Company's capability to correct and recommends the need for outside assistance of vendors, engineering contractors, and consultants as necessary.
7. Trained/experienced/competent with the maintenance of Electrical Equipment in Hazardous Areas (EEHA).

Experience

10+ Years

Level

Senior

Education

Associate's Degree In Instrumentation Technology

Description :

1. Documented key findings during work execution and actively participated in improving the preventative maintenance program.
2. Made modifications to existing conduit and wiring
   Programming, troubleshooting, and making adjustments in the PLC.
3. Programmed, troubleshooted, and maintained advanced PLC/5 and Control Logix.
4. Maintained, troubleshooted, and repaired electronic circuits and control devices.
5. Monitored and provided feedback on equipment conditions and potential failure risks.
6. Contacted vendors and manufacturers as needed for support in resolving issues.
7. Worked any shift, including 12-hour shifts, on-call, holidays, weekends, and overtime as needed.

Experience

7-10 Years

Level

Management

Education

Associate's Degree In Electrical Engineering Technology

Description :

1. Utilized the functions of the maintenance management system to facilitate job plans and record maintenance activities on plant assets.
2. Participated in the planning and execution of chemical plant turnarounds.
3. Assisted in the review, development, and implementation of site preventative maintenance programs.
4. Tuned process control loops and machine control systems, Programmed and troubleshooted DCS, PLC, and HMI interfaces.
5. Troubleshooted and E&I maintenance on up to 2300 V voltage equipment.
6. Inspected, tested, repaired, and maintained the electrical and instrumentation parts of process flows, machinery, and mechanical equipment such as pumps, engines, motors, pneumatic systems and valves, hydraulic systems and valves, conveyor systems, flow meters, and gauges.
7. Read and interpreted P&ID wiring and circuit diagrams, blueprints, engineering drawings, and process and instrument diagrams.

Experience

5-7 Years

Level

Executive

Education

Associate's Degree In Electrical Engineering Technology

Description :

1. Troubleshooted and E&I maintenance on up to 2300 V voltage equipment and high voltage 13.8 kv.
2. Set and calibrated safety limit controls, relief devices, sensors, alarms, check valves, and electrical equipment for temperature, pressure, flow rate, levels, voltage, and current according to service manuals, schematic diagrams, or process and instrumentation diagrams.
3. Started machines and equipment to test operation following repair, Inspected field instrumentation and verification of manufacture calibration, onsite calibration, and testing.
4. Completed electrical work in accordance with NEC, NFPA70E, MSHA standards, and best practice
   Final control element inspection and troubleshooting, repair and rebuild, replacement and installation according to engineering standards, best practices, and manufacturer recommendations.
5. Commissioned and start-up activities including, instrument loop inspection, loop check, configuration, calibration, and testing.
6. Supported and maintained DCS, and PLC-based systems, Worked with industrial machinery or other large systems that require precise control over their operation.
7. Installed electrical components in industrial equipment such as motors, generators, transformers, and pumps.

Experience

2-5 Years

Level

Executive

Education

Associate's Degree In Electrical Engineering Technology

Description :

1. Understood and supported company and site safety policies and performed work-related activities in a safe manner.
2. Recognized unsafe working conditions, coached peers, and suggested new safety standards as appropriate.
3. Performed the necessary activities to operate, maintain, and clean production equipment.
4. Understood, followed and improved documented operational, maintenance, and sanitation standards in a Good Manufacturing Practices (GMP) work environment.
5. Performed equipment changeovers and sanitation activities, and also Performed preventative maintenance activities, work orders, and lubrication in a timely manner to maximize the performance of plant equipment. 
6. Inspected, maintained, troubleshooted, and repaired electrical, instrumentation, controls, and automation equipment and software.
7. Maintained and properly operated electrical testing equipment.

Experience

2-5 Years

Level

Executive

Education

Associate's Degree In Electrical Engineering Technology