Injection Molding Machine Operator Resume Samples

Description :

1. Observe machine operation to detect workpiece defects or machine malfunctions, adjusting machines as necessary.
2. Extract or lift jammed pieces from machines, using fingers, wire hooks, or lift bars.
3. Inspect workpieces for defects, and measure workpieces to determine the accuracy of machine operation, using rules, templates, or other measuring instruments.
4. Position, adjust, and secure stock material or workpieces against stops, on arbors, or in chucks, fixtures, or automatic feeding mechanisms, manually or using hoists.
5. Perform minor machine maintenance, such as oiling or cleaning machines, dies, or workpieces, or adding coolant to machine reservoirs.
6. Set machine stops or guides to specified lengths as indicated by scales, rules, or templates.
7. Select, install, and adjust the alignment of drills, cutters, dies, guides, and holding devices, using templates, measuring instruments, and hand tools.
8. Start machines and turn handwheels or valves to engage feeding, cooling, and lubricating mechanisms.

Experience

2-5 Years

Level

Junior

Education

HS

Description :

1. Verify correct set-up of molds, presses and auxiliary equipment before machine startup.
2. Maintain records and prepare legible reports, including SPC reports, QC inspection reports, housekeeping checklists, mold cavity data sheets, etc.
3. Observe all safety and environmental procedures and good manufacturing practices. 
4. Responsible and accountable for: achieving adequate production levels, maintaining the expected product quality, and keeping the area clean and in order.
5. Operate a group of 16 injection molding machines and auxiliary equipment to cast products from a power mesh to the high-quality products in a safe method.
6. Perform assigned preventative maintenance work Make hourly quality checks on products being produced from established quality standards.
7. Use forklift and pallet jacks to move materials to and from the production area.

Experience

5-7 Years

Level

Executive

Education

BS

Description :

1. Operate metal and plastic molding and casting machines.
2. Mold and cast metal or thermoplastic parts.
3. Design and develop new molds, molding processes, techniques, process improvements, and cost reductions.
4. Develop and document manufacturing instructions and datasheets.
5. Operate compression or injection molding machines.
6. Mix raw plastic material with coloring and hardliner, Install metal mold and run the machine to fill the order.
7. Inspect each part with very high precision measuring equipment and trim off overflow lines.

Experience

2-5 Years

Level

Junior

Education

HS

Description :

1. Operate plastic and rubber molding and casting machines.
2. Mold and cast metal or thermoplastic parts.
3. Design and develop techniques and process improvements.
4. Develop and document manufacturing instructions and datasheets.
5. Operate compression or injection molding machines.
6. Run injection mold machines set mold to call up program troubleshot process till good parts running pack parts. 
7. Basic Machine Maintenance, monitoring machine, switching molds, and operating forklift.
8. Operate production machinery in a safe and efficient manner, maintaining a cleaned workspace.

Experience

7-10 Years

Level

Management

Education

HS

Description :

1. Operates the injection molding machine.
2. Relies on instructions and pre-established guidelines to perform the functions of the job.
3. Responsible for the initial creation of all plastic injection molding pieces to be processed through the machine.
4. Perform visual, in-process and final inspection of parts.
5. Mastered the use of multiple molding machines.
6. Very repetitive, straight forward work, occasionally purging the machine and measuring parts hourly to ensure they were as the customer requested.
7. Ran an injection molding machine, and made different parts for different kinds of cars.

Experience

5-7 Years

Level

Executive

Education

Diploma

Description :

1. Brushed or sprayed mold surfaces with parting agents.
2. Set operating temperatures for each casting.
3. Operated and adjusted heating equipment to melt material, cure and fill molds.
4. Melting extra plastic off, trimming and spraying a protector on the dashboards.
5. Relies on instructions and pre-established guidelines to perform the functions of the job.
6. Responsible for the initial creation of all plastic injection molding pieces to be processed through the machine.
7. Responsible for inspecting, trimming, assembling and packaging molded products with attention to detail to guarantee customer satisfaction.

Experience

5-7 Years

Level

Executive

Education

Diploma

Description :

1. Completed housekeeping and maintenance duties in the production area.
2. Packaged plastic parts at a rate of 60 - 90 per hour.
3. Developed and trained new employees on blow molding and molding process maintenance.
4. Ran plastic injection molding machines and peripheral equipment.
5. Exemplified a positive attitude as a team member in a dynamic, fast-paced environment.
6. Prepared slitting documents, core-tags, box labels, and quality documents and training documents without immediate supervision.
7. Informed relief shift and superiors about machine production and status, material processes, department needs, and any problems.

Experience

5-7 Years

Level

Executive

Education

Certification

Description :

1. Mold and cast metal or thermoplastic parts.
2. Operate compression or injection molding machine grind scraps into powder.
3. Read specifications to determine setup and prescribed temperature and time settings.
4. Inspect products for surface defects and flaws.
5. Eliminate the production of defective parts and products.
6. Regulate molding temperature, volume, pressure, and time.
7. Set up and Operate blow molding machines to mold plastic products according to specifications.
8. Test finished products from machines and weight tests to determine the accuracy of the operations of the machine.

Experience

10+ Years

Level

Senior

Education

Diploma

Description :

1. Assisted machine operators with finished pieces.
2. Fabricated large and small parts per drawing and assembled parts as required.
3. Maintained a necessary level of communication between shifts.
4. Ensured that all health and safety guidelines were followed.
5. Made sure that products were produced on time and are of good quality.
6. Monitored product standards and quality-control programs.
7. Operated machinery used in the production process.
8. Examined products to verify conformance to quality standards.

Experience

7-10 Years

Level

Management

Education

Diploma

Description :

1. Operate injection mold machine by injecting a polymer into the screw to form mold.
2. Keep a document of all temperature, pressure.
3. Document all information of lot on-device history record.
4. Inspect parts for defects and test parts hourly on planar and Instron.
5. Log all hours of the product being under nitrogen and vacuum chambers.
6. Place tablet on the product after scanning and verifying label count and ship out.
7. Always made more production parts than the amount set daily with good quality.

Experience

5-7 Years

Level

Executive

Education

Certification

Description :

1. Clean the machine before the start of the shift.
2. Take out part after they have been molded.
3. Responsible for making medical products for our customers.
4. Operate machines that molded rubber into syringe stoppers.
5. Train to operate all machines in the medical plant.
6. Run machines that made rubber extruder, plastic extruder and injection molded parts for the automotive industry.
7. Assembly, running machines, general.
8. Operate plastic and metal molding casting machines.

Experience

2-5 Years

Level

Junior

Education

HS

Description :

1. Mold and cast metal or thermoplastic parts.
2. Operate compression or injection molding machine grind scraps into powder.
3. Read specifications to determine setup and prescribed temperature and time settings.
4. Inspect products for surface defects and flaws.
5. Eliminate the production of defective parts and products.
6. Regulate molding temperature, volume, pressure, and time.
7. Insert laminate blank and cut overlay in die cutter.
8. Insert overlay into an injection molder and cycle injection molder.

Experience

10+ Years

Level

Senior

Education

Diploma