Simulation Engineer Resume Samples

Description :

1. Designed and developed highly complex real-time software for utilization in United Defense's armor simulators, with the goal of replacing expensive, proprietary systems with less-expensive standard systems.
2. Designed and developed a C++ multithreaded 3D positional sound application that replaced an expensive proprietary system that was used in all of United Defense's Simulators.
3. Used other windows based technologies such as; MFC and Winsock32 APIs.
4. Created two UDP network interfaces that received DIS and data packets from other external subsystems to call upon the sound application.
5. Used Object Oriented Methodologies to design and develop a highly flexible and scalable real-time C++ application that had the ability to interface with multiple hardware devices and communicate with multiple subsystems through network interfaces.
6. Application utilized an API for multiple PCI data acquisition boards with digital and analog IO channels, API for a PCI optical encoder, API for a PCI 1553 data bus controller, and an API to communicate with multiple serial devices.
7. Designed and developed a window-based C++ DLL to increase the fidelity of soldiers training for the Bradley M2A3 Fighting Vehicle Simulator by adding integrated combat command and control (IC3) digital communications for man-in-the-loop training.

Experience

5-7 Years

Level

Executive

Education

BS In Electrical Engineering

Description :

1. Checked the DCS logic and later it will be used for operator training.
2. Provided an OTS(Operator Training Simulator) for the Oil Sand plant.
3. Responsible for the modeling of the tailing area.
4. Scope of the project was P&ID validation and OTS modeling of this 345MW power plant.
5. Responsible for Steam-Water System, flue gas condensation of power boiler.
6. Developed the Attitude Control Algorithms used to simulate the Attitude Control System and all related sensors (Sun and Earth) used by the Training.
7. Designed, prototyped & assessed (e.g., through pilot plant testing and validation) packaging technologies and concepts to product and process specifications (e.g., functionality and operational feasibility), as well as the developed value chain and economic feasibility analysis for candidate packaging solutions.

Experience

7-10 Years

Level

Management

Education

BS

Description :

1. Worked on complete seat meshing and model development for 1st, 2nd, and 3rd-row seats in ANSA software.
2. Worked on debugging all models before delivering them abroad with LS-DYNA.
3. Check runs and full runs for penetrations, contacts, and model behavior from a crash point of view.
4. Worked on model development for the front crash, rear impact, luggage retention, seat belt anchorage test environment set up, and respective 5th, 50th, and 95th percentile dummies.
5. Did seat belt routing for all set-ups.
6. Worked on SFAD and its setup.
7. Worked towards the new modeling methods to improve accuracy and reduce the time required for model build-up.

Experience

2-5 Years

Level

Junior

Education

ME In Mechanical Engineering

Description :

1. Created DCS deliverable for Ford Chrysler and GM using Process Simulate which in turn created an outline for robot programmers to follow while programming dual check safety.
2. Created weld paths for spot welders, MIG welders, sealers, and material handlers in Process Simulate.
3. Modeled tooling, cleaning out useless data and added kinematics, in both Robcad and Process Simulate allowing the tool designs to be proven in simulation.
4. Added new tooling models into the Process Simulation project libraries giving simulation engineers access to the models so they could be used in the simulation studies.
5. Created line simulation which utilized simulated I/O signals and logic modules to simulate how the line would respond to the PLC and various control inputs.
6. Which in turn cut the debug time of the PLC to Robot interface by more than 50%.
7. Worked with design group on the tool and gun testing and approval which cut down on the number of modifications the tools would need to function in the real world.

Experience

5-7 Years

Level

Executive

Education

Associates In Industrial Electrical Technologies

Description :

1. Worked on history matching, calibrating, and prediction of black oil CHEARS models for West Africa fields.
2. Worked included data gathering, normalizing of relative permeability data, and capillary pressure data.
3. Performed various transforms to determine permeability and initial fluid saturations for input for the history matching phase.
4. Used pipe flow to determine pis for the producers for the calibration phase.
5. Participated in injector and producer placement for evaluation during the prediction phase.
6. Had to troubleshoot decks when convergence problems developed.
7. Programmed and analyzed simulation models of manufacturing systems.

Experience

0-2 Years

Level

Entry Level

Education

MS In Petroleum Engineering

Description :

1. Built nonlinear and explicit models for verification and functional goals.
2. Consulted on tolerance and datum strategies for new and production model products.
3. Scope included predicted function, manufacturability, and assembly concerns.
4. Support past initial delivery to provide expertise for revisions.
5. Developed and introduced new methods of using the software to present a more accurate picture of the problem presented.
6. Used tolerance and datum structure knowledge to design a lightweight fixture for the simultaneous location of body fascia.
7. Developed and implemented innovative systems and procedures that allow optimization in all phases of the process design and development process.

Experience

5-7 Years

Level

Executive

Education

BS In Mechanical Engineering

Description :

1. Ran simulations of parts outsourced by Ford to tier-one suppliers.
2. Determined the feasibility and recommend changes if needed, try to reduce material utilization, and develop.
3. Developed a process to improve material usage from 63% to 76%.
4. Determined the feasibility as well as designed the manufacturing process for low-volume parts.
5. Software baseline installation and scenario development.
6. Visualized material movement in production and warehouse using Witness14 software Involved planning of scheduled investments with highest profit yield.
7. Performed permutation and combination to identify the bottleneck and that maximized throughput and profit.

Experience

0-2 Years

Level

Entry Level

Education

MBA In International Business

Description :

1. Performed integration and testing of operator training simulators for combined cycle and nuclear power plants.
2. Responsible for testing, troubleshooting, and modifying power plant control systems to achieve a fully functional operator training simulator.
3. Responsible for generating proposals for power plant operator training simulator projects including proposals for nuclear and combined cycle power.
4. Managed the execution of simulator projects by procuring material, coordinating schedules, handling shipping logistics, approving vendor invoices.
5. Spearheaded the installation and implementation of all medical, simulation, A/V, and IT-related equipment in GRU's brand new, state-of-the-art, 35.
6. Included, but are not limited to, purchasing recommendations.
7. Oversaw installations, troubleshooting issues, and collaborated with outside vendors.

Experience

7-10 Years

Level

Management

Education

MBA in International Business

Description :

1. Helped the TAD software developers find and correct several Attitude Modeling problems with the TAD software.
2. Developed Computer-generated process models designed to optimize production.
3. Received GM's President Council Award for improvements.
4. Maintenance on the 757, 767, and 777 simulators.
5. Performed maintenance, PMs, preflight, and post-flight checks on the 737-800 simulator.
6. Worked with medical professionals to construct and validate data analysis for CT scanners utilization in the emergency department.
7. Developed a simulation model to optimize resource utilization and decrease patient queuing time.

Experience

7-10 Years

Level

Management

Education

MBA in International Business

Description :

1. Led the development and global deployment of reduced hardware simulation environments which reduced the cost of a simulation environment.
2. Led the development and deployment of simulators to more than quadruple capacity in under 2 years' time.
3. Developed real-time locomotive models using both Simulink and MatrixX to deliver cycle-accurate models for use within the simulation environments.
4. Received more than a dozen spot bonuses for exceptional work and on-time delivery of business-critical simulation needs.
5. Developed computer visualization tools to help evaluate and guide negotiations for Mergers and Acquisitions.
6. Extensive use of game theory and dimensional reduction techniques.
7. Cell building for robotic applications like spot welding, stud welding, material handling, and hemming.

Experience

7-10 Years

Level

Management

Education

MBA in International Business