Welding Inspector Resume Samples

Description :

1. Ensure that proper documentation is done in all received Materials and carry out an inspection at the site.
2. Daily surveillance on Baking & Holding oven temperature and also the storage condition of welding consumables.
3. Inspection of received pipes/pipe fittings and mechanical equipment.
4. Preparation of bill of materials to sub-contractors for appropriate fabrication and erection.
5. Field inspection and confirmation of various installation of pipeline materials in accordance with its isometric.
6. Inspection and confirmation of various internals materials for columns and vessels 
7. Daily Surveillance on the storage of all Project Materials o Ensuring that all non-conforming materials are segregated and kept on quarantine to avoid usage.
8. Carrying out Inventory and reconciling materials received against material issued for fabrication on a weekly basis.
9. Maintain a comprehensive calibration log and to ensure the use of only calibrated inspection measuring & testing equipment.
10. Preparing the entire final documentation and traceability of quality records known as Final Dossier Book.

Experience

2-5 Years

Level

Junior

Education

Certification

Description :

1. Performed as a Certified Welding Inspector and technical specialist in a quality assurance capacity.
2. Provide quality control inspections and quality factory surveillance, during manufacturing Travel.
3. Performing "Pre-Shipment Inspections" (PSIs) and 'Source Inspections" (SI) at different fabricators for various products being manufactured for the contract.
4. Perform Ultrasonic Testing and Magnetic Particle Testing verification behind Quality Control (QC) inspectors.
5. Performed final visual weld review and inspection, per D1.1/D1.5 per contract documents.
6. General inspection on material ID and release of fracture critical and non-fracture critical material, bolt, nut and washer ID and release, etc.
7. Analyzed and evaluate work sequences, construction methods, work-in-progress and building priorities.
8. Monitor all required construction for conformance with contract documents.

Experience

2-5 Years

Level

Junior

Education

Diploma

Description :

1. Conduct visual inspection on completed welds Report and documents Inspection results.
2. Day to day supervision of construction activities including relevant quality controls during prefabrication and site construction.
3. Review, monitor and report daily the status of inspection and test activities.
4. Check safety documents and permits at site Supervise procedures.
5. Liaise with personnel in assigning NDE test on welded joints based on project specifications.
6. Review the procedures and results in line with project specification.
7. Ensure that welders comply with HSE requirements, also monitoring pre & post-weld heat treatment.
8. Assist in Visual inspection of fit-up, in-process welding, pre & post-weld inspection at various sites in line with project requirements.

Experience

10+ Years

Level

Senior

Education

Certification

Description :

1. Carry out material inspection and review of goods inward inspection report.
2. Review of the Technicians certificates and performance prior to the commencement of inspections.
3. Inspection of the calibration status of all welding machines and measuring instruments and equipment.
4. Inspection of pipe fit-up for subsea structure prior to welding with reference to approved drawings and welding procedure carrying out before, during and after welding inspections.
5. Review and sign-out all the reports from contractor testing company Inspection of fit-up for beams and structures for sea fastening.
6. Inspection of all welding activities for sea fastening and review of all the reports.
7. Prepare and forward daily report and job progress to the client on daily basis.

Experience

2-5 Years

Level

Junior

Education

Diploma

Description :

1. Verify specifications set in the pre-job are being met by all contractors involved in the project.
2. Assure proper material and grades as expected out are being used.
3. Track and record all material heat numbers verifying correct MTR's on materials.
4. Ensure all welding related activities are conducted in accordance with all local municipal, in addition to complying with all company and API 1104 standards and regulation.
5. Verify and record all proper calibrations of equipment and tools used welding and bolt up the process of the project.
6. Inspect all welding equipment welding machines regulators cables and grinders for proper and safe use.
7. Inspect and record proper welding process is being conducted such as volts, amperage, high idle amperage, and travel speed according to the welding procedure set by API 1104.

Experience

2-5 Years

Level

Junior

Education

Diploma

Description :

1. Inspect units coming from the Weld Line for leaks and proper hardware installation prior to painting.
2. Ensure finished units are on the correct pallet/pad and are properly attached.
3. Ensure units are moving smoothly on the conveyor and do not get hung up and damage equipment or product or fall and cause injury.
4. Routinely stop units from going to the next operation when one find faulty welds and/or parts that are incorrect, not properly installed or installed in the wrong location.
5. Created work packages and test packages which included weld maps and flange bolt up maps.
6. Performed daily inspections of welders, welding rods, and rod temperature, also was instructed to witness hydro tests on different piping systems.

Experience

7-10 Years

Level

Management

Education

BE

Description :

1. Conducted internal and external inspection to ensure that it meets the necessary code and quality standards.
2. Ensured that all the safety procedures are maintained while using the various equipment in the welding procedures.
3. Maintained all the documentation for the inspection and repair work carried on the facility and kept a record of the submitted forms.
4. Maintained all paperwork such as completing the forms for the customers and the company.
   
5. Administered the various aspects of the welding process and helped in maintaining quality control on the procedure.
6. Monitored the welding procedure to ensure the authenticity of the process.
7. Managed the inspection process by identifying any defects in the process.

Experience

10+ Years

Level

Senior

Education

Diploma

Description :

1. Conducted dimensional checks to ensure welded structures are within the designed tolerances.
2. Controlled the proper storage and use of welding consumables (filler wires and electrodes).
3. Cross Verification of Welding Machines Calibration, Measuring instruments calibration, Pressure Gauge calibration, etc. and maintaining all related file and records.
4. Carried out a visual inspection, welding consumable verification, dimensional check, performance test, welder qualification, welder training, and performance monitoring.
5. Carried out inspection of the joints to be welded before, during and after fit-up to ensure that there are no defects and the dimensions are correct.
6. Reviewed plans and specs during the schematic design of pre-construction.
7. Submitted daily inspection reports containing weld and x-ray count for the total job.

Experience

2-5 Years

Level

Junior

Education

BE

Description :

1. Inspected in high-demand and strong accountability environments on projects completed for the client.
2. Inspection services covered all aspect of pipeline construction including design, install hydrostatic and pneumatic testing, tie into existing facilities.
3. Responsible for reporting drilling activities and completion schedules for client's rigs in the area of the basin.
4. Multiple well-connection pipelines and facilities for collecting of natural gas and crude oil.
5. Pipeline and facilities gathering system collecting natural gas and crude oil including multiple-well connections.
6. Mainline crude oil gathering pipeline extension with central pigging facility for additional gathering.
7. Documented all weld/joint numbers and locations by creating isometric drawings of all tie-ins and fabrication.

Experience

2-5 Years

Level

Junior

Education

Certification

Description :

1. Inspected and tested welded joints of work in progress and of completed units for visible defects, correct dimensions, joint strength, and conformance.
2. Verified alignment and dimensions of product and setup of machines and fixtures used for work in progress.
3. Marked defective pieces and made recommendations for scrapping or methods for re-working.
4. Welded, tested, and inspected metal samples to determine most effective welding process and technique and be designated Performance Test Inspector.
5. Liaised to order gas, tools, equipment, and other items necessary for mission completion.
6. Ensured adherence to procedure manual for cut and cap on lateral lines, as well as proper hydro-test procedures.
7. Checked elevation head pressures and ensured Certs were current and up to date.

Experience

2-5 Years

Level

Junior

Education

Diploma

Description :

1. Documented and did all as builds for work, as progressed on tie in the crew.
2. Worked with the survey on joint and weld information helped and track joint information as needed.
3. Mentored coating of welds on tie in and directional bore pipe.
4. Worked with environmental monitored dewater of ditches and all environmental issues concerning new construction.
5. Assisted on mainline hydro testing of 42" and 20" from Superior to Owens Station.
6. Checked elevation head pressures and ensured Certs were current and up to date.
7. Verified plots and proper equipment was on job checked cert.
8. Performed regular job site observations to provide immediate and look-ahead direction for all general and sub-contractor personnel.

Experience

0-2 Years

Level

Entry Level

Education

Diploma