Wire Harness Assembler Resume Samples

Description :

1. Maintained a clean and organized workstation. Be certified in small gauge wire harness assembly.
2. Built and terminated wire harnesses for Class A Motor Coaches, train new employees, communicate to the supervisor of issues and progression.
3. Assembled complex wire harness for contracted customer 
4. Checked the quality of all wires, crimp quality, and verify Hi-Pot procedures for Multi-Conductor wires Continually improve processes for production efficiency.
5. Worked in different areas of the production floor, and for different customers when production demand dictates.
6. Contracted projects due to NCR Reports Accomplishments Improved quality and efficiency on Contracted Project.
7. Helped to improve processes for better production and quality improvement for the entire company.
8. Ensured more work and extended contracts through quality and production improvement on designated contract.

Experience

5-7 Years

Level

Executive

Education

Diploma

Description :

1. Specialized in the manufacture and design of cable harnesses and assemblies.
2. Measured and accurately cut the cable of various gauges to length via machine, for example, Artos and Komax.
3. Applied terminals via Amp machine to cable to be plugged into two, four, and twenty-four pin cable housing.
4. Plugged in wires of various colors into cable housing as the diagram indicates.
5. Sealed assembly by heating shrink tubing, label and mark finished wire harness assembly to be processed by Q.C.
6. Routed as well as tied wires to form wire harness cable used in electrical electronic equipment or systems.
7. Selected wires of the specified color, marking, or length and additionally loop wires between guide pegs on harness board.
   
8. Attached ends of wires to components, plugs, or terminal strip, using soldering iron or crimping device.

Experience

5-7 Years

Level

Executive

Education

Electronics

Description :

1. Routed and tied wires to form wire harness used in electrical and electronic equipment or systems.
2. Checked Proper Paper Work and Enter Test Results Data into Server According to FDA - Guild lines.
3. Dismantled devices to gain access to and remove defective parts.
4. Interpreted safety policies/practices to employees including enforcing safe work practices.
5. Observed mechanical devices in operation and listen to their sounds to locate causes of trouble.
6. Soldered irons, crimpers, wire strippers, and heat guns in the construction and repair of wire harnesses for large recreational vehicles.
7. Examined blueprints to check for wiring sequences. Base mechanical knowledge to troubleshoot and fix equipment in all functional areas.

Experience

2-5 Years

Level

Junior

Education

Diploma

Description :

1. Built wire harnesses for military H2 SUV, sport utility trucks, and John Deere farm machinery.
2. Wrote and Compiled ABR Syntax 'code' for Dynalab wire-harness test systems -to ensure correct routing and continuity of wires.
3. Translated Dynalab programs (imported from Mexico) from Spanish to English.
4. Updated visual references for harness builders from Spanish to English (using PowerPoint's drawing tools, company's printer, and laminating devices).
5. Constructed 'boards' for wire-harness assembly, using blueprints, metal braces, other tools, and 'holders'.
6. Wired and circuited these 'holders' into a sequence based on information offered via spreadsheets.
7. Operated 'Vision System' on Stoneridge's 'MD Line'. Practiced and implied safety procedures whenever necessary.
8. Provided clean work environments, and practiced Lean Manufacturing in the workplace, to help keep down overhead costs.

Experience

5-7 Years

Level

Executive

Education

Master's

Description :

1. Routed and tied wires to form wire harness used in electrical and electronic equipment or systems.
2. Read instructions, such as work orders, diagrams, and wire lists to determine materials needed and sequence of assembly.
3. Selected wires of the specified color, marking, or length and loops wires between guide pegs on harness board.
4. Wrapped and tied wires together at designated points to form harness, manually or using a tie-wrap gun.
5. Applied sealing liquid to secure knots in ties, using a brush.
6. Inserted cable in plastic tubing or inject plastic sealant around terminals to protect the cable from dust and moisture.
7. Tested wiring continuity, using continuity tester and marked identifying data on a completed harness.

Experience

5-7 Years

Level

Executive

Education

General Education

Description :

1. Fabricated Harnesses for military vehicles and airplanes from government contacts.
2. Tested and troubleshoot harnesses that had issues.
3. Helped the lab solder on circuit boards, tinned wires, fabricated panels for cockpits.
   
4. Charged of the stock room where all of the inventory was held.
5. Reserved parts for work orders and pulled them, as well as did inventory year.
6. Shipped employees putting kits together for customers overseas, shipping computer servers, harnesses and other items we made in house.
7. Trained employees to build harnesses, shipping and being in charge of the stockroom.

Experience

7-10 Years

Level

Management

Education

Diploma

Description :

1. Collected wires and all necessary components in order to assemble wire harnesses in accordance with each set of blueprints specifications.
2. Assembled each wire harness a thorough inspection of the harness had to be made to assure complete accuracy.
3. Processed all necessary information had to be logged into the departmental system and on a paper form.
4. Demonstrated desire to work and willingness to learn by maintaining a perfect attendance history.
   
5. Hired on through them as a full-time employee.
6. Organized and ability to maintain great time management skills as well as being goal-oriented.
7. Sealed assembly by heating shrink tubing, label and mark finished wire harness assembly to be processed.
   

Experience

5-7 Years

Level

Executive

Education

General Studies

Description :

1. Laid out and located structural components. Completed the necessary paperwork.
2. Determined assembly and installation sequence.
3. Notified designated personnel of improper machine functioning.
4. Assembled from blueprints, charts, diagrams, specification sheets.
5. Performed finishing operations, including assembling, using screws, fastening nuts and bolts.
6. Fallowed Blueprint specifications Attention to detail QC inspections Re-work Bagging and label Use of hand tools.
7. Assembled harnesses to specifications in a reasonable amount of time with minimum errors.

Experience

2-5 Years

Level

Junior

Education

Diploma

Description :

1. Followed assembly drawings, layout diagrams and performed all tasks, in a compliant manner.
2. Assembled all electrical components and sub-assemblies.
3. Examined and verified the quality of all components, before and after assembly.
4. Prepared and maintained accurate quality and assembly documentation, as required.
5. Adhered to established environmental, health and safety rules and met quality and performance standards.
6. Prepared and check various electro-mechanical parts for assembly.
7. Assembled and set up sub-assemblies in cases and cabinets.
8. Conducted check on assembled products to detect and repair faults.

Experience

7-10 Years

Level

Management

Education

Commerce

Description :

1. Organized a fundraiser for Wildlife Foundation, a penny war raised hundreds of dollars that were donated.
2. Competed in dozens of competitions, a total of fifteen gold medals.
3. Assembled airplane wire harnesses.
4. Built wiring harnesses to customer blueprints and diagrams.
5. Routed wires throughout the cabin, trunk, and engine area Fasten wires to the car body with clips.
   
6. Assembled wire harnesses for MOD ambulances.
7. Worked under the microscope is just amazing.

Experience

2-5 Years

Level

Junior

Education

Psychology

Description :

1. Laid out and located structural components.
2. Determined assembly and installation sequence.
3. Notified designated personnel of improper machine functioning.
4. Assembled from blueprints, diagrams, specification sheets.
5. Performed finishing operations, including assembling, fastening nuts and bolts.
6. Experienced with calipers, gauges, measuring tapes, measuring tools.
7. Inserted wires into correct connectors and locations.

Experience

2-5 Years

Level

Junior

Education

Diploma